fatigue crack propagation behaviour in ultra

Near-Threshold Fatigue Crack Propagation in Ultra

Fatigue crack propagation behavior of an ultra-high strength steel (300-M) has been investigated in humid air over a very wide spectrum of growth rates from 10/sup -8/ to 10/sup -1/ mm/cycle. Particular emphasis has been devoted to the influence of mean stress (or load ratio R = K/sub min//K/sub max/) and microstructure on fatigue crack growth near the threshold stress intensity for crack

Near-Threshold Fatigue Crack Propagation in Ultra

Fatigue crack propagation behavior of an ultra-high strength steel (300-M) has been investigated in humid air over a very wide spectrum of growth rates from 10/sup -8/ to 10/sup -1/ mm/cycle. Particular emphasis has been devoted to the influence of mean stress (or load ratio R = K/sub min//K/sub max/) and microstructure on fatigue crack growth near the threshold stress intensity for crack (PDF) Characteristic Fatigue Crack Growth Behavior of Low fatigue crack propagation behavior, we clari ed the cause of . In order to clarify an influence of hydrogen on the fatigue crack propagation in ultra-low frequency region, we investigated the

(PDF) Characteristic Fatigue Crack Growth Behavior of Low

fatigue crack propagation behavior, we clari ed the cause of . In order to clarify an influence of hydrogen on the fatigue crack propagation in ultra-low frequency region, we investigated the (PDF) Prediction of Fatigue Crack Growth Behaviour in structureproperty relationship of ultra-fine grained Al 2014 alloy The influence of these parameters on lifetimes and fatigue crack propagation behavior being determined by microstructural

(PDF) Prediction of Fatigue Crack Growth Behaviour in

structureproperty relationship of ultra-fine grained Al 2014 alloy The influence of these parameters on lifetimes and fatigue crack propagation behavior being determined by microstructural (PDF) Uniaxial compressive fatigue behavior of ultra-high Uniaxial compressive fatigue behavior of ultra-high performance concrete reinforced with super-fine stainless wires. crack stable propagation stage. and instability failure stage. When the

A comparison of fatigue-crack propagation behavior in

product form on the fatigue-crack propagation (long-crack) resistance of A1-Li alloys. Crack- growth behavior is examined in two AI-Li alloys:high-strength 2090-T8X, which has been cited as a replacement for the AI-Zn-Cu-Mg alloy 7075- T6, and low strength and high-toughness 2091- Characteristic Fatigue Crack Growth Behavior of Low The fatigue crack propagation mode with brittle striation arose from HELP-related hydrogen-assisted microvoid formation at the crack tip and its subsequent coalescence with the main crack. 23,24) On the other hand, hydrogen hardly affected the fatigue crack growth rate at a test frequency of 1×10 3 Hz. In order to interpret the

Characteristic Fatigue Crack Growth Behavior of Low

The fatigue crack propagation mode with brittle striation arose from HELP-related hydrogen-assisted microvoid formation at the crack tip and its subsequent coalescence with the main crack. 23,24) On the other hand, hydrogen hardly affected the fatigue crack growth rate at a test frequency of 1×10 3 Hz. In order to interpret the FATIGUE CRACK PROPAGATION BEHAVIOUR OF Fatigue crack propagation behaviour of short cracks 151 Fig. 4. The surface view of a small semi-elliptic crack. Reference to Figs 5 (a) and (b) and to Fig. 2 above leads to two main conclusions.First, there is an approximate correlation between 1, and d, and between I, and d for a wide range of materials. It was difficult to obtain accurate values of d from the published work

Fatigue Behavior of Ultra-Fine Grained Ti-6Al-4V Alloy

This paper reviews fatigue strength, fatigue crack initiation and fatigue crack propagation behavior of protium treated ultra-fine grained Ti-6Al-4V alloy in air and in 3% NaCl aqueous solution. Fatigue Crack Propagation - an overview ScienceDirect TopicsRegion 2 represents the stable crack propagation behavior and in region 3 the fatigue crack growth rate is higher than that predicted for region 2. However, in this study we can observe something remarkable about the crack propagation behavior, that is, the behavior can be divided into two regions and confirms the existence of a transition point.

Fatigue crack propagation behavior of AZ31 Mg alloy in

Jun 29, 2011 · The fatigue crack propagation (FCP) behavior of extruded AZ31-F was examined in conjunction with crack closure phenomena. FCP experiments were carried out in an ultra-high vacuum system using a fatigue test machine under a constant load amplitude. Fatigue crack propagation behavior of ultra high molecular Fatigue crack propagation behavior of ultra high molecular weight polyethylene under mixed mode conditions. Dr. K. E. Elbert. Sibley School of Mechanical and Aerospace Engineering, Cornell University, Ithaca, New York 14853. Search for more papers by this author. T. M. Wright.

Fatigue crack propagation behavior of ultra high molecular

Fatigue crack propagation behavior of ultra high molecular weight polyethylene under mixed mode conditions. Elbert KE(1), Wright TM, Rimnac CM, Klein RW, Ingraffea AR, Gunsallus K, Bartel DL. Author information:(1)Sibley School of Mechanical and Aerospace Engineering, Cornell Fatigue crack propagation behavior of ultra high molecular and The effect of waveform on the fatigue crack propagation behaviour of ultra high molecular weight polyethylene, in Advances in Fracture Research. Proceedings of the 7th International Conference on Fracture, and (eds.), Pergamon Press, New York, 1989, pp. 1305-1311.

Fatigue crack propagation behavior of ultrahigh molecular

Fatigue crack propagation behavior of ultrahigh molecular weight polyethylene Fatigue crack propagation behavior of ultrahigh molecular weight polyethylene Connelly, G. M.; Rimnac, C. M.; Wright, T. M.; Hertzberg, R. W.; Manson, J. A. 1984-01-01 00:00:00 The relative fatigue crack propagation resistance of plain and carbon fiberreinforced ultrahigh molecular weight polyethylene Fatigue crack propagation behavior of ultrahigh molecular Fatigue crack propagation in both materials proved to be very sensitive to small changes in the applied cyclic stress intensity range. A 10% increase in stress intensity resulted in approximately an order of magnitude increase in fatigue crack growth rate.

Fatigue crack propagation behaviour derived from SN

ABSTRACT The crack propagation law was derived from the SN data in the very high cycle fatigue of a bearing steel. The propagation rate, da/dN (m/cycle), of surface cracks was estimated to be a power function of the stress intensity range, K (MPam) with the coefficient C s = 5.87 × 10 13 and the exponent m s = 4.78. The threshold stress intensity range was 2.6 MPam. Fatigue crack propagation behaviour derived from SN data ABSTRACT The crack propagation law was derived from the SN data in the very high cycle fatigue of a bearing steel. The propagation rate, da/dN (m/cycle), of surface cracks was estimated to be a power function of the stress intensity range, K (MPam) with the coefficient C s = 5.87 × 10 13 and the exponent m s = 4.78. The threshold stress intensity range was 2.6 MPam.

Fatigue crack propagation behaviour in ultra-fine grained

Fatigue growth behaviour of long cracks in an ultra-fine grained steel (grain size 1m) was investigated. The influence of tensile mean stress on propagation threshold and propagation behaviour Influence of microstructure on near- threshold fatigue Fatigue crack propagation behaviour of an ultra-high strength, silicon-modified AISI 4340 alloy steel (300-M) has been investigated in moist air over an extremely wide range of growth rates from 10-8 to 10-1mm/cycle. Particular emphasis has been devoted to the influence of microstructure on fatigue-fracture behaviour near the threshold stress

Influence of microstructure on near-threshold fatigue

Nov 08, 1977 · Fatigue crack propagation behaviour of an ultra-high strength, silicon-modified AISI 4340 alloy steel (300-M) has been investigated in moist air over an extremely wide range of growth rates from 10 8 to 10 1 mm/cycle. Particular emphasis has been devoted to the influence of microstructure on fatigue-fracture behaviour near the threshold stress intensity, K 0 below which crack growth Mechanisms of fatigue-crack propagation in ductile and The mechanisms of fatigue-crack propagation are examined with particular emphasis on the similarities and differences between cyclic crack growth in ductile materials, such as metals, and corresponding behavior in brittle materials, such as intermetallics and ceramics. This is achieved by considering the process of fatigue-crack growth as a mutual competition between intrinsic mechanisms of

Micro Fatigue Crack Propagation Behavior in a Duplex

Fatigue crack propagation behaviors in a duplex stainless steel have been studied using an in-situ SEM/EBSD fatigue test and a conventional da/dN test. Crack propagation behaviors in grain, effect of Schmid factor, propagation cross the grain or phase boundaries have been discussed. Crack propagation occurs mainly in the grains with a high Schmid factor, but the crack can also propagate Near-Threshold Fatigue Crack Propagation in Ultra-High Fatigue crack propagation behavior of an ultra-high strength steel (300-M) has been investigated in humid air over a very wide spectrum of growth rates from 10 8 to 10 1 mm/cycle. Particular emphasis has been devoted to the influence of mean stress (or load ratio R = K min /K max) and microstructure on fatigue crack growth near the threshold stress intensity for crack propagation, K 0.

Near-Threshold Fatigue Crack Propagation in Ultra-High

Fatigue crack propagation behavior of an ultra-high strength steel (300-M) has been investigated in humid air over a very wide spectrum of growth rates from 10 8 to 10 1 mm/cycle. Particular emphasis has been devoted to the influence of mean stress (or load ratio R = K min /K max) and microstructure on fatigue crack growth near the threshold stress intensity for crack propagation, K 0. Near-Threshold Fatigue Crack Propagation in Ultra-High Fatigue crack propagation behavior of an ultra-high strength steel (300-M) has been investigated in humid air over a very wide spectrum of growth rates from 10 8 to 10 1 mm/cycle. Particular emphasis has been devoted to the influence of mean stress (or load ratio R = K min /K max) and microstructure on fatigue crack growth near the threshold stress intensity for crack propagation, K 0.

Open Access proceedings Journal of Physics:Conference

The objective of this study is to understand the fatigue crack propagation behavior of a titanium alloy, Ti-6Al-4V, refined to an ultra-fine grain level by the newly-developed protium treatment. The tension-compression (R = 1) fatigue tests of specimens with sharp, shallow notches were conducted Open Access proceedings Journal of Physics:Conference The objective of this study is to understand the fatigue crack propagation behavior of a titanium alloy, Ti-6Al-4V, refined to an ultra-fine grain level by the newly-developed protium treatment. The tension-compression (R = 1) fatigue tests of specimens with sharp, shallow notches were conducted

Relationship between dynamic fatigue crack propagation

The relationship between dynamic crack propagation behaviour and viscoelasticity of NR/VMQ composites Average values and standard deviations of dynamic fatigue crack growth rate d c /d N at constant G input of 1000 J m 2 are shown in Fig. 7. Transition behavior from Mode I cracking to In summary, the study reported on fatigue crack propagation tests at 450 °C and crystal plasticity analysis conducted for Ni-base single crystal superalloy at low temperature. The aim was to clarify fatigue crack propagation behavior, especially the transition from Mode I to crystallographic cracking.

Transition behavior from Mode I cracking to

In summary, the study reported on fatigue crack propagation tests at 450 °C and crystal plasticity analysis conducted for Ni-base single crystal superalloy at low temperature. The aim was to clarify fatigue crack propagation behavior, especially the transition from Mode I to crystallographic cracking. Ultra-slow Fatigue Crack Propagation in Metallic Alloysfrequencies, even cracks growing at ultraslow velocities (< 10-10 m/cycle) can lead to failure of a component. Consequently, it is of prime importance to know the fatigue crack propagation behavior and, moreover, the threshold-stress intensity factor for fatigue cracks at very high frequency. This paper is dedicated to a comparative

Ultra-slow Fatigue Crack Propagation in Metallic Alloys

frequencies, even cracks growing at ultraslow velocities (< 10-10 m/cycle) can lead to failure of a component. Consequently, it is of prime importance to know the fatigue crack propagation behavior and, moreover, the threshold-stress intensity factor for fatigue cracks at very high frequency. This paper is dedicated to a comparative Very high cycle fatigue and fatigue crack propagation Jan 01, 2017 · Results of fatigue crack propagation rate measurements for the batches B and D are shown in Fig. 14. In the Paris region, both the samples have nearly similar crack propagation behavior, as can be observed from their slopes. The difference in the two batches at the threshold value of stress intensity factor range is distinct.

Fatigue crack propagation behaviour in ultra-fine grained

Mar 01, 2005 · The fatigue crack propagation threshold (K thR) seems to be defined by the condition that the cyclic plastic zone at the crack tip is of the order of grain size (r pc 1 m=d), and the influence of the mean stress seems to be defined by the maximum stress intensity factor (K max) through its influence on crack closure behaviour, the crack

Leave a Comment